Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden errors.

Moderators: Site Moderators, FAHC Science Team

bruce
Posts: 20824
Joined: Thu Nov 29, 2007 10:13 pm
Location: So. Cal.

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by bruce »

Everything in that log is showing Machine ID: 3. You have not changed it yet.
HendricksSA
Posts: 336
Joined: Fri Jun 26, 2009 4:34 am

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by HendricksSA »

ChrisM101, you will probably need to change your machine ID. Stop the client. Change to the right directory and start the client using FAH_GPU3.exe -configonly

While you're going through the machine IDs just pick something other than 3 and different from all the others on this pc. Finish the config. Restart the client normally and you should see the new ID.

For better instructions on the use of configonly - see this: http://folding.stanford.edu/English/WinGPUGuide#ntoc3
ChrisM101
Posts: 12
Joined: Tue Mar 22, 2011 4:06 pm

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by ChrisM101 »

Yeah i cant manually change it , so ive got a request with the GPU TRACKER Developer , see if i can get an answer on changing it.
HendricksSA
Posts: 336
Joined: Fri Jun 26, 2009 4:34 am

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by HendricksSA »

Wow, I wasn't sure what the impact of Tracker2 would be. Please let us know how that goes. Looking forward to reply.
rjbelans
Posts: 77
Joined: Fri Nov 27, 2009 2:48 am

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by rjbelans »

The developer has a forum to get help directly: http://fahtracker.forumotion.com/forum

And there are usually a few people that can help out over in the folding section of evga.com/forums/

My suggestion would be to create a temporary desktop shortcut to the FAH_GPU3.exe and change the properties to Start In:...\FAH GPU Tracker V2\GPU# (# depends on which card it is happening to) and also add " -gpu# -configonly" (without quotes) to the end of the Target line. When you start it using this shortcut, it should now go through the normal configuring process. You can check to make sure everything is correct as you go through, but the main thing is to set the machine ID to something that is not currently being used by another client (usually 10, 11, 12, etc. works). Now (assuming you have deleted all of the work files, etc.), once you start the client in Tracker, it should pick up a new work unit.

Hope that helps. I'll check back in later to see how it's going.
Image
Image
folding@evga - Donor Advisory Board Representative
ChrisM101
Posts: 12
Joined: Tue Mar 22, 2011 4:06 pm

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by ChrisM101 »

thanks rj... I will try that, unfortunately im already at work so itll be lunch before i can.
ChrisM101
Posts: 12
Joined: Tue Mar 22, 2011 4:06 pm

Re: Project: 6806 (Run 3987, Clone 2, Gen 10) - Sudden error

Post by ChrisM101 »

RJs method worked, so i got a 6801 WU now...
Post Reply